-
Philips
MD1.2E CTV
Service Mode
There is a small Service jumper to short on the small signal PCB. When the TV is in this first level service mode, you can go in the second level service mode by pressing both MENU
and - keys on top of the TV at the same time. There you can read much parameters and proceed with most of the adjustments. In fact this method let you use an ordinary Remote control but you also need to open the back
cover. With the special service remote control,
a special code is sent to enter the service mode. Philips
MG3.1E CTV
Service Mode
Option 1: In the TV-set itself is a 3-pin connector with which either SERVICE-DEFAULT or
SERVICE-MODE can be activated. This connector is depicted 0356 (SERVICE-PINS) on page K7 (TXT&CONTROL). Shorting pins 1-2
will activate SERVICE-MODE. Shorting pins 2-3 will activate SERVICE-DEFAULT. Option 2: Activate these modes using the remote control. Obviously option 2 is the preferred method because the settings have to be changed using a remote control anyway.... To activate SERVICE-DEFAULT: Press 0 6 2 5 9 6 and then
the [menu] button. The message `Service Default' appears and channel `SER T' will be selected. This only sets some settings to a preset value
(color/brightness/volume and such). This mode is primarily intended to be used when the non volatile memory has been replaced. It is then loaded with the default values. To activate SERVICE-MODE: Press 0 6 2 5 9 6 and then
the [i+] button. After pressing 0 6 2 5 9 6 the message `Dealer' should have appeared.
Do not worry about the channel changing while you press the numbers.
Service technicians have the means of entering service mode using a special remote control. Philips
29PT9416
MG7.1
CTV
Service Mode
Use the standard remote control an *** in a special sequence 0 6 2 5 9 6 followed by pressing the 'MENU' button. If the main menu also appears with the service menu just press
'MENU' again to clear it. The other way is to short the two service pins on the signal panel
(pins 2 and 3 of connector 0356). The advantage of this last method is that all the software protections are turned off.
Philips
Y6
CTV
Service Mode
Use the standard remote control an *** in a special sequence 0 6 2 5 9 6 followed by pressing the 'MENU' button. If the main menu also appears with the service menu just press
'MENU' again to clear it. Philips
VR210/58
VCR Modulator off
Without cassette. Press and hold SYSTEM till
'G591' appears. Press and hold CLEAR(CL) till
'MOFF' appears. Exit: TV/STANBY. Philips VR210/58
VCR Modulator on
Without cassette. Press and hold SYSTEM till
'MOFF' appears. Press and hold CLEAR(CL) till
'G591' appears. Exit: TV/STANBY. Philips VR220/58
VCR
Child Lock
Cancel
Press CHILD LOCK (***-simbol) on the RC for 5s with the VCR switched on. Philips
VR220/58
VCR Modulator on/off
Without cassette. Press and hold STOP on the
RC and then press STOP/EJECT on VCR.
Select the line 'MODULATOR' on the TV screen
or 'MOD+' in the display with P+/-. In the display select 'OFF' / 'MOD-' (modulator off) with VOL-
or 'MOD+' (modulator on). Confirm with OK. Exit with MENU
Philips
VR220/58
VCR Modulator preset
Without cassette. Hold the STOP button on the RC. In addition press the STOP/EJECT button on the VCR until the pre-set modulator frequency appears in the display, e.g. 'M591'
(591MHz or 36 ch. UHF). Select line 'OPTIMIZE FREQUENCY' using P+/-. Enter new
modulator frequency with the numbers 0-9. In line 'SOUND SYSTEM' select the TV system using VOL+/-. 'G' = PAL B/G. 'K' = SECAM D/K. Confirm with OK. 'STORED' will appear briefly on the screen.
Philips
VR220/58
VCR Reset to factory settings
Disconect from the mains power supply. Press and hold the STANDBY/ON button on the device and reconnect to the mains power supply. Release the button when 'OSD' appears in the VCR display.
Philips
VR400/58
VCR
Auto ST-BY
off
Press and hold STOP till [] appears. Philips
VR400/58
VCR Modulator off
Without cassette. Press and hold SYSTEM till
'G591' appears. Press and hold CLEAR(CL) till
'MOFF' appears. Exit: TV/STANBY. Philips VR400/58
VCR Modulator on
Without cassette. Press and hold SYSTEM till
'MOFF' appears. Press and hold CLEAR(CL) till
'G591' appears. Exit: TV/STANBY. Philips VR400/58
VCR Modulator preset
Without cassette. VCR st-by. Press and hold
SYSTEM till 'G591' appears. System change:
SELECT.
Freq. Change: P +/-.
Store: OK. Exit:
TV/STANBY.
Revox D-TV C9003
CTV
Service Mode
On the local control press function *** five times
(indication "Service" will appear), afterwards within a sec. press *** "MEN" on the remote control.
Store: X. Exit: TV.
-
Saba ULTRACOLOR
T55U42 T55U43
T63U42 T63U43
ICC5115ML 110
ICC5116MM 90° CTV Combination Lock Cancel
Switch off set with main switch. Switch on set with main switch and during doing this press the buttons + and - of volume control on the set's control bord simultaneously until the display lights. Display: SS... Press the button
'S' on the RC. Switch off with RC. Now the combination lock is unlocked and one can switch on again in the normal manner.
Saba
ICC9
CTV
Service Mode
Switch off TV with RC (st-by). Switch off TV with main switch. Wait a few sec till ST_BY LED
switch off. Simultaneous press VT button on RC and switch on TV with main switch. Press VT button again. (WARNING: scart must be free.) Saba
T7032VT TX92
CTV
Hotel Mode
Cancel
Put TV into standby, then turn power off, then turn power on whilst holding standby button on remote and step through menus to vol set and increase level to max.
Salora
28N8S
2B-F CTV
Service Mode
Quick press: --\-, MENU, TV. Salora
17/21SF 25/28X71
25/28SP50
STEREO PLUS CTV
Service Mode
MUTE --> OK (M) --> TV Controls:
cursor buttons. Store:
OK (M). Exit: TV
Samsung
CB-14F1 CB-20P30
CB-20H1 CB-20S20
CB-21H1 CB-21P30
CB-21S20 CB-3373
CB-5020 CB-5073
CB-5079 CB-5320
CB-5373 CB-5379
S15A CTV
Service Mode
STAND-BY --> DISPLAY --> P.STD --> MUTE --> POWER ON.
Controls:
VOL +/-, CH +/-. Exit:
POWER OFF. Samsung CK5038
SCT11B CTV
Service Mode
STAND-BY --> P.STD --> HELP --> SLEEP --> POWER ON.
Controls:
VOL +/-, CH +/-. Exit:
STATUS.
Samsung
CX5944 CX6844
SCT12B CTV
Service Mode
STAND-BY --> P.STD --> HELP --> SLEEP --> POWER ON.
FACTORY MODE: set PSL=15 and PVA=63. Controls:
VOL +/-, CH +/-. Exit:
STATUS Samsung
CB-14V10 CB-3373
CB-14V20 CB-5073
CB-20P30 CB-5079
CB-20S10 CB-5373
CB-20S20
CB-21P30
CB-21S10
CB-21S20
SCT13B CTV
Service Mode
STAND-BY --> P.STD --> HELP --> SLEEP --> POWER ON.
Controls:
VOL +/-, CH +/-. Exit:
STATUS. Samsung CS7272
SCT51A CTV
Service Mode
PICTURE OFF --> SLEEP --> P.STD --> MUTE --> PICTURE ON
Samsung
CS-721
CS-723
SCT52A CTV
Service Mode
PICTURE OFF --> SLEEP --> P.STD --> MUTE --> PICTURE ON
Samsung
TVP3350
TVP5050
SCV11A SCV11B
CTV/VCR Service Mode
STAND-BY --> P.STD --> MENU --> SLEEP --> POWER ON
-
Schneider
DTV 1
CTV
Service Mode
Simultaneous press Service-button on digi- bord & button C on RC.
Selection: Bass +/-. Adjust: Volume +/-.
Store: T. Exit: TV.
Schneider
DTV 100
CTV
Service Mode
Simultaneous press red & blue buttons on RC then (in 5 sec.) simultaneous press P- & P+ on local keyboard.
Commands: arrows. Store: OK.
Exit: TV.
Schneider
DTV 2
CTV
Service Mode
Like DTV 1 or simultaneous press Service- button (down right on RC) & C button on RC. Selection:
Bass +/-. Adjust: Volume +/-. Store: IDEAL. Exit:
TV. Schneider DTV 3
CTV
Service Mode
Simultaneous press red & blue buttons on RC then (in 5 sec.) simultaneous press P- & VOL+ on local keyboard.
Selection: wheel. Adjust: ring. Store:
red button. Exit:
OFF. Schneider TV 4
CTV
Service Mode
Simultaneous press red & blue buttons on RC then (in 5 sec.) simultaneous press P- & VOL+ on local keyboard.
Selection: P +/-. Adjust: VOL +/-. Store: auto. Exit:
OFF. Schneider STV7128
TV 8
CTV
Service Mode
Simultaneous press red & blue buttons on RC then (in 5 sec.) simultaneous press P- & VOL+ on local keyboard.
Selection: P +/-. Adjust: VOL +/-. Store: auto. Exit:
OFF. Schneider TV 9
CTV
Service Mode
Simultaneous press red & blue buttons on RC then (in 5 sec.) simultaneous press P- & VOL+ on local keyboard.
Selection: P +/-. Adjust: VOL +/-. Store: auto. Exit:
OFF. Schneider STV355FST CTV
Service Mode
MENU --> SERVICE --> OK --> 089
SEG
11AK18
CTV
Service Mode
MENU 1 6 7 5
SEG
11AK19
CTV
Service Mode
MENU 4 7 2 5
Seleco STEREO PLUS CTV
Service Mode
MUTE --> OK (M) --> TV Controls:
cursor buttons. Store:OK (M). Exit:TV
Sharp
4BSA CTV
Service Mode
Short conntacts 2 & 6 on bord TB connector and press button 'MODE' on RC. Remove short. Store:auto.
Exit:'MODE'. Sharp
63CS-03S CS
CTV
Service Mode
Press and hold buttons VOL- and PR+ on the local keyboard and then switch on with main switch.
Store:'POWER'. Sharp
D3000
CTV
Service Mode
Press Service-button on Digi-modul. Storen/off.
Exit:Service button. Sharp
Euro-DS1
CTV
Service Mode
Short conntacts 2 & 6 on Digi Modul Service Slot and then press button 'MODE' on RC. Storeromb-symbol) on RC.
Exit:standby, switch off, switch on, remove short. Sharp
54AT-15SC CTV
Service Mode
Press and hold buttons VOL- and PR+ on the local keyboard and then switch on with main switch.
Store:'POWER'. Sharp
DV-5401S CTV
Service Mode
Locate place for 2 buttons on local keyboard
(main board) S754-MODE and S755-PRESET. Enter:short S754 (-SERV-).
Commands:CH +/-. Store:short S755.
-
Siemens
FS369M4
CS9409
CTV
Service Mode
Info Center' --> 'Special Functions' --> 'Service'
--> Code Number 089
Siemens SAT Programm Lock
Unlock: Press ***-symbol and 6 1 0 1.
Silva STV355FST CTV
Service Mode
MENU --> SERVICE --> OK --> 089
Sony
KV-E2531
KV-E2931
KV-E3431
AE-2
CTV
Service Mode
Turn on the main power switch of the set while pressing any two buttons on the front panel.
'TT' will appear on the upper right corner of the screen. Press the 'MENU' button on the RC.
In menu select 'DEMO' and press 'OK'. Select DEVICE coresponding to the adjustment you need. Store: OK. Exit: turn off.
Sony
KV-2170
KV-2180
KV-2540
BE4
CTV
Service Mode
? --> 5 --> VOL+ --> TV --> MENU Exit: 00
Sony
KV-B2911
CTV
Service Mode
Turn on the main power switch of the set while pressing any two buttons on the front panel.
'TT' will appear on the upper right corner of the screen. Press the 'MENU' button on the RC.
In menu select 'DEMO' and press 'OK'. Select DEVICE coresponding to the adjustment you need. Store: OK. Exit: turn off.
Sony
KV-G21M1
CTV
Service Mode
Switch TV to STANDBY.
DISPLAY --> 5 --> VOL+ --> POWER
Telefunken
ICC9
CTV
Service Mode
Switch off TV with RC (st-by). Switch off TV with main switch. Wait a few sec till ST_BY LED
switch off. Simultaneous press VT button on RC and switch on TV with main switch. Press VT button again. (WARNING: scart must be free.) Telefunken
STEREO PLUS CTV
Service Mode
MUTE --> OK (M) --> TV Controls:cursor buttons. Store:OK (M).
Exit:TV Telefunken TX-90
CTV
Service Mode
Switch off TV with RC (st-by). Switch off TV with main switch. Wait a few sec till ST_BY LED
switch off. Simultaneous press VT button on RC and switch on TV with main switch. Press VT button again.
Telefunken
TX-91
CTV
Service Mode
Switch off TV with RC (st-by). Switch off TV with main switch. Wait a few sec till ST_BY LED
switch off. Simultaneous press VT button on RC and switch on TV with main switch. Press VT button again.
Thomson
ICC19
CTV
Service Mode
Switch to Standby. Switch off with the mains switch. Press and hold blue button and then switch on with the mains switch. Press blue button again. Exit: switch off with mains switch. Thomson
ICC19
CTV
Service Mode
Switch to Standby. Switch off with the mains switch. Press and hold 'PROG-' and 'VOL-' and then switch on with the mains switch. Exit: switch off with mains switch.
Thomson
ICC9
CTV
Service Mode
Switch off TV with RC (st-by). Switch off TV with main switch. Wait a few sec till ST_BY LED
switch off. Simultaneous press VT button on RC and switch on TV with main switch. Press VT button again. (WARNING: scart must be free.) Thomson
TX-90
CTV
Service Mode
Switch off TV with RC (st-by). Switch off TV with main switch. Wait a few sec till ST_BY LED
switch off. Simultaneous press VT button on RC and switch on TV with main switch. Press VT button again
-
Thomson
TX-91
CTV
Service Mode
Switch off TV with RC (st-by). Switch off TV with main switch. Wait a few sec till ST_BY LED
switch off. Simultaneous press VT button on RC and switch on TV with main switch. Press VT button again.
Toshiba a2150
S5E CTV
Service Mode
Press 'MUTE' button. Press and hold 'MUTE' button and press 'MENU' on local keyboard. Select: PR nr.. Adjust: VOL+/-. Store: auto. Exit: 'STANDBY'. Test picture: 'AV'.
Toshiba
2876DD
2988DG CTV
Service Mode
Press 'MUTE' button. Press and hold 'MUTE' button and press 'MENU' on local keyboard. Select:PR+/-.
Adjust:VOL+/-. Store:auto.
Exit:'STANDBY'. Test picture: 'AV'.
Universum
6000
CTV
Service Mode
Switch on with main switch. Press 'MENU',
'TV', 'i'. If TV is still in st-by press 2x'TV', 'i'. Select and adjust with cursors. Store: 'OK'.
Exit: switch off with main switch
-
Orient 37 Kilit Çözme
Sol üst köşede *** . . .
şekil olur ise üç kere pp tuşuna bas
Sonra menü den kilidi kaldır.
Sağ alt köşede asma kilit olur ise
U.kumanda üzerinden osd tuşuna 8 sn basılı tut işlem tamam.
buda benden
-
bilgi ve paylaşım için teşekkürler
-
premier 7750t
abicim bende premier 7750t tv var görüntü kendi kendine zoom yapmış gibi büyüdü nasıl düzeltebiliriz yardımcı olabilirmisin birde bu tv nin servis giriş kodu nedir biliyormusun teşekkür ederim
-
eline emeğine sağlık ustam
-
