Konuya Etiketlenenler

Teþekkur Teþekkur:  0
Beðeni Beðeni:  0
Sayfa 1/2 12 SonSon
17 sonuçtan 1 ile 10 arasý

Konu: Micom'dan No Micom'a Dönüþüm (Sadece ustalar için)

  1. #1

    Kullanýcý Bilgi Menüsü

    Standart Micom'dan No Micom'a Dönüþüm (Sadece ustalar için)

    Selam Arkadaþlar,

    Öncelikle Uydu dünyasý için Çeviri'yi yapan arkadaþýmýz ............................... Kadir YOÐURTÇU'ya hep birlikte teþekkür ediyoruz..


    Metnin orijinali Fransýzca'dýr.

    Ýþlem çok basit!.. Kýrgýzistan'da olduðum için deneme imkaným bulunmamaktadýr. Bu nedenle þimdilik Türk ustalar bu iþlemi uygulamalýdýr.

    Kaon 570H’nizi 570’e DÖNÜÞTÜRMEK
    Version 1.0
    18 Ocak 2007

    Bu dönüþümü niçin yapmalýyým?
    Bu dönüþümü yapmalýsýnýz çünkü Kaon 570H’nin uzun zamandan beri destek uygulamalarý yoktur. (Büyük bir ihtimalle yeni ürünlerin kolayca satýlmasý için) bununla birlikte 570 serisinin desteði mevcuttur.

    570H ile 570 arasýnda ne fark var?
    570H’yi 570’e dönüþtürdüðümüzde sabit diske kaydetme özelliðini kolayca uygulayabileceksiniz.

    Acaba bu dönüþüm kalýcý mýdýr?
    Hayýr, kalýcý deðil uygulamayý geri çekmek mümkündür.

    Bu muhteþem dönüþümün temel özelliði nedir?
    570H serisi ile 570 serisi arasýndaki en temel fark “Display” özelliðidir. 570H serisinin “Display” özelliði, 570’in “Display” özelliði ile uyumlu deðildir!!! 570H’nin “Display” özelliði zaten dönüþümden sonra devre dýþý kalacak, 570’in Display’i aktif hale gelecektir.

    Peki ya HD... Display tamamen mi devre dýþý kalacak ?
    Evet, bu uygulamanýn kaçýnýlmaz sonucudur. Ama diðer yandan düzenli olarak güncelleyebileceðiniz, 12.01.A5 “Firmware” ile çalýþacak bir dekodöre sahip olacaksýnýz.

    Bu dönüþümün uygulanmasý sýrasýnda dikkat edilecek baþka hususlar var mý acaba?
    Evet, bu dönüþtürme sonrasýnda 570H’nin “HW” su 12.01.A5 olacaktýr. Bu da sadece Firmware’i deðiþtireceðiz anlamýna gelmez. Ayrýca Bootload’ ý da deðiþtirmek gerekecektir.

    !!! BOOTLOAD DEÐÝÞTÝRMEK MÝ? !!! ANNECÝÐÝM KORKUYORUM!!!!
    Evet çok haklýsýnýz Bootload’ a dokunmaktan her zaman çekinmek gerekir. Ama bizim modelimiz olan Kaon’un her iki Bootload’ý da pratik olarak birbiriyle uyumludur. Eðer pensler karýþýrsa bu çok da önemli deðildir. Zira bu durumun düzeltilmesi için dekodere portalden giriþ yapýlabilir.(Bkz. bu dokümanýn sonundaki ‘Öneriler’ kýsmý.)

    Tamam, her þey yolunda elimde bir klavuz var.Bu iþi kolaylýkla, sorunsuzca halledeceðim..... :-)

    Uyarý :Hiçbir þekilde JTAG’ a baþvurmaksýzýn daha önce birçok defa Kaon’u modifiye etmeme raðmen yaptýðýnýz her iþlemden sadece kendinizin sorumlu olacaðýnýzý hatýrlatmak isterim.

    Pekala, þimdi iþimize bakalým.... Yukarýda da belirtildiði gibi parçalarýn modifiye edilmesi esnasýnda Bootload’ ýn deðiþtirilmesi ve Firmware’in güncelleþtirilmesi gerekmektedir. Bu durumda yapýlacak ilk iþ kýlavuz özelliði taþýyan bu word dosyasýný iyice incelemenizdir. Ayrýca aþaðýdaki bilgileri kontrol ettikten sonra dönüþtürme iþlemine gerçekten hazýr olup olmadýðýnýzý kontrol ediniz.

    Yeni bootload, Kaon Team grubunun 2.1.9V4 serisi olmalýdýr.
    Firmware’in güncellenmiþ hali ise “Favori Upload” ta bulabileceðiniz son geliþtirilmiþ 12.01.A5 serisi olmalýdýr. Kaon Team Grubunun 1.19V4 serisine ait olan Bootload’ýn geri planda da çalýþmasýný istemeniz durumunda bunu 570H serisi dekodörünüzden elde edebilirsiniz.

    Modifikasyonun verimli olmasý için aþaðýdaki iþlemleri sýrasýyla yapmanýz daha iyi olacaktýr.

    1. Öncelikle izlemekte olduðunuz kanallarýnýzý ve favori kanallarýnýzýn tümünü silebilirsiniz.(Tavsiye edilmez)

    2. Modifikasyon iþleminden önce Kaon’daki 2.1.9V4 Bootload’ý þarj ediyoruz.
    Kaon, modifikasyona uygun olsa da iþlemden sonra Display ile uyumlu olmayan bir Bootload’ýmýz olacaðýndan veri akýþý artýk mümkün olmayacaktýr.

    3. Þimdi de Display özelliðini bu word dosyasýndaki açýklamalara uygun olarak modifiye ediyoruz.

    4. Tüm anakart baðlantýlarýný yeniden yapýyoruz.

    5. Kaon’u arkasýnda yer alan açma-kapama düðmesinden açýp çalýþtýrýyoruz.
    Ýþlemden birkaç saniye sonra Display üzerinde « -- » þeklinde bir görüntü belirecektir.

    6. KUP’ yi internetten temin edeceðimiz Firmware 12.01.A5 ile birlikte ‘Enginer’ modunda hazýrlýyoruz.

    7. Kaon’un ön yüzündeki « Stand By » düðmesine basýyoruz. Böylelikle Firmware transferi baþlamýþ olacaktýr.

    Transfer iþlemi sonunda bir sorun çýkarsa « exemple... ERR : on STB -> PC » paniðe kapýlmayýn. Bunlar aktarýlan verilerdir. Yukarýdaki iþlem sýrasýna geri dönerek 5. Iþlemden yeniden baþlayabilirsiniz.

    Transfer tamamlandýðýnda modifikasyonumuzu da tamamlamýþ olacaðýz. Böylece dekodörümüz kullanýma uygun hale gelecektir.


    Artýk Display tamamen kullaným dýþý olacaðýndan Kaon’un çalýþtýrýlmasý da biraz farklý olacaktýr. Bu durum aþaðýda açýklanmýþtýr :

    Kaon dekodörü arka tarafta bulunan düðmesini açtýðýmýz zaman ekranda « -- » þeklinde cihazýmýzýn Stand By durumunda olduðunu belirten bir görüntü belirecektir. Maalesef gerçekleþtirdiðimiz dönüþtürme iþleminin ardýndan bu mod dan uzaktan kumanda yoluyla çýkmak artýk mümkün olmamaktadýr. Bu durumda Display’de dekodörün ön yüzünde bulunan « on » yazýsýný görebilmek için. Stand By düðmesine basmak gerekecektir. Bu iþlemin ardýndan dekodör açýlmazsa kesin olarak çalýþmasý için uzaktan kumandanýzýn Stand By tuþuna basmanýz gerekir. Dekodörün arkasýndaki düðmeyi kapattýðýmýz takdirde yukarýdaki iþlemlerin her defasýnda tekrar edilmesi gerekmeyecektir. Zira dekodör bir kez çalýþmaya baþladýðýnda uzaktan kumandasý da tamamen kullanýma açýlýr ve hiçbir sorun olmadan açma kapama iþlemlerini yapabilirsiniz.(Örneðin Firmware’i güncelleme iþlemlerini yapabilirsiniz.)



    Display’in modifiye edilmesi
    Ýþlem öncesi dekodörünüzün fiþini prizden çekmeyi unutmayýnýz.
    Display’in sökülüp takýlmasý oldukça kolaydýr. Hemen detaylara geçelim. Eðer Display’i sökersek ve anakarttan çýkarýrsak, küçük J6 köprüsünün lehimini çýkarabilmek için elektronik baský devresini de çýkarmak gerekmektedir...

    ( Resim üzerindeki açýklama : J6 köprüsünü çýkarýn)

    Bu Linki Görmeniz Ýçin SupersatForuma Uye Olmanýz Gerekmektedir.



    Ardýndan Display’in bir grup baðlantý kablosunu anakarttan çýkarmanýz gerekecektir.
    (1 No’lu kablo siyah olan kablodur.)
    Kablolarý yerinden çýkarmak için çok ince aðýzlý bir tornavida ile dar yuvalarýn üstüne bastýrmak yeterli olacaktýr. Bunu yaparken baðlantý kablolarýný birer birer çekip çýkarmanýz gerekecektir. Önlem olarak çýkardýðýnýz her kablonun uçlarýný bir miktar isolebant ile kaplayarak yalýtýmý saðlamanýz gerekir.



    (Resim üzerindeki açýklama : Baðlantý kutucuðundan 1,2,3 ve 11 nolu kablolar dýþýndaki tüm kablolarý çýkarýn.)

    Bu Linki Görmeniz Ýçin SupersatForuma Uye Olmanýz Gerekmektedir.



    Þimdi yapmamýz gereken þey 11. Kabloyu baský devresinin biraz üstünden kesmek ve bu kabloya ek yaparak J6 köprüsüyle baðlantý yapacak þekilde uzatmaktýr. (Ýþlemin en baþýnda bu köprüyü çýkarmýþtýk.)
    ( 1. Resim üzerindeki açýklama : 11. Kabloyu devrelerin biraz üstünden kesiniz.)

    Bu Linki Görmeniz Ýçin SupersatForuma Uye Olmanýz Gerekmektedir.

    Bu Linki Görmeniz Ýçin SupersatForuma Uye Olmanýz Gerekmektedir.
    (Resim üzerindeki açýklama : Kabloyu buraya uzatýn ve lehimleyin.)
    !!! DÝKKAT DELÝÐÝ KARIÞTIRMAYIN !!!
    Ve iþte oldu ! Ýþlem çok da zor olmasa gerek.


    Eski Kaon 570H’yi yeniden nasýl çalýþtýrabiliriz ?

    Aþaðýdaki uygulamalrý sýrasýyla gerçekleþtirdiðinizden emin olun.

    1. Kaon Team’in 1.1.9V4 Bootload’ýnýzý þarj edin.

    2. 570H için Firmware’i güncelleyin.

    3. Display üzerinde yapýlmýþ modifikasyonlarý kaldýrýn. 11 nolu kablonun uzantýsýný anakart üzerindeki eski yerine tekrar lehimleyin. anakart üzerindeki baðlantý kutucuðuna tüm kablolarý yerleþtirin. J6 köprüsünü yerine yerleþtirin.

    Öneriler:

    Kaon, orijinal durumdaki Display ve Bootload 2.1.9V4 ileyken transfer yapmak mümkün deðildir. Zira, iþlemden birkaç saniye sonra Display ile baðlantýsý kesilmiþ olacaktýr. Bu durumu gidermek için ne yapmak lazým?

    Ýki olasýlýk vardýr:

    Ya Display yukarýda açýklandýðý gibi modifiye edilir ya da Display anakarta baðlanýr ama ayný anda baðlantý kutucuðu da hafifçe yerine yerleþtirilir, transfer baþlar. Sonra, portalden baðlantýnýn kesilmesini engellemek için hýzlýca baðlantý kutucuðu geri çekilir.


    Firmware’in deðiþtirilmesi esnasýnda karþýlýklý olarak dört basamaklý dijital deðerden(PÝN kodu) altý basamaklý dijital bir deðere geçilebilir. Aþaðýdaki tabloda mönüye yeni bir deðer giriþini deneyebilmeniz için bazý orijinal kodlar verilmiþtir.


    0000
    Tuþlar: R Yeþil Sarý
    463330


    Söz konusu bu Word dosyasýný ilk okuduðunuzda yapýlacak iþlemler size biraz
    « karmaþýk »gelebilir. Fakat size belirtilen açýklamalarý, verilen kurallara uygun olarak yaptýðýnýzda dönüþtürme iþleminin aslýnda çok kolay olduðunu göreceksiniz.



    BAÞARILAR... ;-)

  2. #2

    Kullanýcý Bilgi Menüsü

    Standart

    Tesekkurler güzel çalýþma konuyu stickledim ..

  3. #3

    Kullanýcý Bilgi Menüsü

    Standart

    anlatým için teþekkürler

  4. #4

    Kullanýcý Bilgi Menüsü

    Standart

    please if u can translate all this in english, if this information usefull for DSC 911Z 13.42.65

    Thanks

  5. #5

    Kullanýcý Bilgi Menüsü

    Standart

    French translate

    Transformer son Kaon 570H en 570
    Version 1.0 18 janvier 2007
    Pourquoi devrais-je faire cette transformation ?
    Car il n'y a plus de support pour le Kaon 570H depuis longtemps (sans doute pour vendre plus facilement leurs nouveaux produits) par contre il y en a encore pour le 570.
    Quel différence il y a t'il entre un 570H et un 570 ?
    Le 570H permet de faire des enregistrements sur disque dur chose qui en sera plus possible de faire sur le 570 après la modification.
    Est-ce que la modification est définitive ?
    Non, il suffit de retirer la modification pour retrouver son 570H
    Est-ce que la modification est difficile à faire ?
    Non, il n'y a qu'une soudure à faire sur un fil et aucune manipulation sur la carte mère.
    En quoi consiste cette fameuse modification ?
    La différence fondamentale entre le 570H et le 570 est le Display.
    Les 2 Display ne sont pas compatibles !!!
    Il faudra donc désactiver en partie le Display du 570H et en conséquence après la modif le Display
    ne fonctionnera plus que partiellement.
    Donc en plus du HD... le Display ne sera plus opérationnel non plus ?
    Oui, c'est le prix à payer, mais au moins on aura un Décodeur qui fonctionnera avec les firmwares 12.01.A5 qui sont mis à jours régulièrement.
    Il y a t'il encore d'autres choses à faire à part la modification ?
    Oui, une fois le 570H modifié son HW deviendra 12.01.A5 et il faudra non seulement lui mettre le firmware approprié mais aussi lui changer son Bootload.
    !!! CHANGER DE BOOTLOAD !!!! MAMAN J'AI PEUR !!!!
    Oui vous avez raison, il faut toujours avoir peur de toucher au bootload, mais pour notre modèle de Kaon les 2 bootloads sont pratiquement compatibles entre eux. Si on se mélange les pinceaux ce ne sera pas trop grave et nous aurons toujours accès au décodeur par le port série pour y remédier. (Voir « Conseils » en fin de Doc)
    Bon OK, explique toujours la modif... et je verrai bien après si je me décide.... :-)
    Remarque :
    Bien que j'ai déjà réalisé la modification sur plusieurs Kaon sans jamais avoir eu recours au
    JTAG sachez que vous êtes le seul responsable de vos actes.

    Bien... allons y... Comme déjà commenté plus haut, en plus de faire une modification physique au Display il faudra aussi changer le Bootload et le firmware. Donc, la première chose à faire sera de vous les procurer s'ils ne se trouvent pas inclus dans l'archive de cette doc.
    Le nouveau bootload sera le 2.1.9V4 du groupe KaonTeam.
    Le firmware sera le dernier 12.01.A5 que vous trouverez sur votre Upload favori.
    Procurez vous aussi le bootload 1.1.9V4 du groupe KaonTeam pour la cas ou vous décideriez faire
    marche arrière et pouvoir ainsi retrouver votre décodeur 570H.
    Lidéal pour faire la modification est de procéder dans cet l'ordre.
    1 - Nous sauvons d'abord nos chaînes et favoris pour le cas ou ils seraient effacés. (en principe non)
    2 - Nous chargeons le bootload 2.1.9V4 dans le Kaon.
    A partir de ce moment et bien que le Kaon soit opérationnel il ne sera plus possible par le port série d'envoyer quoi que se soit au Kaon car nous aurons un Bootload qui ne sera plus compatible avec le Display.
    3 - Nous modifions donc notre Display comme expliqué un peu plus loin pour le rendre compatible.
    4 - Une fois modifié nous reconnectons le tout à la carte mère.
    5 - Nous allumons le Kaon avec le bouton arrière.
    Après quelques instants nous verrons apparaître « -- » sur le Display
    6 - Nous préparons le KUP en mode Enginer (barre espace du clavier du PC) avec le firmware 12.01.A5 que nous aurons trouvé sur Internet.
    7 - Nous appuyons sur le bouton « Stand By » qui se trouve sur la face avant du Kaon... et le
    transfert du firmware devrait commencer.
    S'il y a un problème à la fin du transfert « exemple... ERR : on STB -> PC » pas de panique, c'est des choses qui arrivent, il suffit de recommencer le transfert à partir du point 5
    Une fois le transfert achevé nous avons terminé notre modification et notre décodeur est
    opérationnel.
    Dorénavant comme le Display ne sera plus complètement fonctionnel le démarrage du Kaon sera un peu différent, voici donc la marche à suivre:
    Lorsque nous l'allumons le Kaon par l'interrupteur arrière nous voyons apparaître sur le Display « -- » qui nous indique que notre appareil est en Stand By... malheureusement suite à la modification réalisé il n'est plus possible de le sortir de ce mode via la télécommande, il faudra donc appuyer sur le bouton « Stand By » de la face avant pour voir apparaître le « on » sur le Display. Ensuite, si le décodeur ne démarre toujours pas nous appuyons sur le bouton « Stand By » de la télécommande pour le mettre définitivement en service.
    Cette procédure ne devra être répétée que si l'on coupe le décodeur avec le bouton arrière car une fois le décodeur en service la télécommande est complètement opérationnelle et on peut sans problème l'allumer et l'éteindre avec celle-ci (par exemple pour faire une mise à jour du firmware).

    Modification physique du Display.
    Avant tout n'oubliez pas de retirer la prise électrique de votre décodeur.
    Le démontage du Display est très simple, je vous passerai donc les détails.
    Une fois le Display démonté et déconnecté de la carte mère il faudra retirer le circuit-imprimé à fin
    de pouvoir dessouder le petit pont J6....
    Bu Linki Görmeniz Ýçin SupersatForuma Uye Olmanýz Gerekmektedir.

    Ensuite il faudra retirer une partie des fils du connecteur du Display qui se connecte sur la carte mère. (Le fil noir est le N°1)
    Pour pouvoir retirer les fils il suffit d'appuyer avec un tournevis très fin dans le rainures et tirer sur le fils pour les extraire du connecteur un par un. Par précaution une fois le fils retirés il faudra isoler les bouts avec un peu de toile isolante.
    Bu Linki Görmeniz Ýçin SupersatForuma Uye Olmanýz Gerekmektedir.

    Il ne nous reste plus qu'à couper le fil 11 à hauteur du circuit imprimé et à le prolonger jusqu'au pont J6 (celui que nous avons retiré au début)
    Bu Linki Görmeniz Ýçin SupersatForuma Uye Olmanýz Gerekmektedir.

    Bu Linki Görmeniz Ýçin SupersatForuma Uye Olmanýz Gerekmektedir.

    !!! ATTENTION A NE PAS VOUS TROMPER DE TROU !!! Et voilà le travail... vous conviendrez que c'était pas bien complexe.

    Comment faire marche arrière et récupérer son bon vieux 570H
    A réaliser dans l'ordre :
    1. Charger le bootload 1.1.9V4 du groupe KaonTeam
    2. Charger le firmware pour le 570H
    3. Enlever les modifications faites sur le Display:
    Enlever la rallonge du fil 11 et ressouder celui-ci comme avant de l'avoir coupé. Remettre tous les fils dans le connecteur qui va a la carte mère. Remettre le pont J6
    Conseils:
    Lorsque le Kaon se trouve avec le Display dans l'état original mais avec le Bootload 2.1.9V4 il n'est pas possible de faire des transfert vers le Kaon car la communication est interrompue après quelques secondes par le Display. Que faire dans ce cas pour s'en sortir ?
    Deux possibilités:
    Soit on modifie le Display comme expliqué plus haut
    Soit on connecte le Display à la carte mère mais en enfonçant légèrement le connecteur et une fois le transfert commencé... on retire rapidement le connecteur pour éviter que le Display ne vienne interrompe la communication par le port série.
    Lors du changement de firmware il se peut que l'on passe d'un code PIN de 4 digits à un de 6 digits ou vice-versa. Voici donc quelques codes d'origine à essayer pour avoir à nouveau accès au Menu.
    0000
    Touches: Rouge Vert Jaune Bleu
    463330
    Bien que cette Doc vous semblera sans doute un peu « complexe » à la première lecture... soyez convaincus que la modification sera très simple à faire et si vous suivez l'ordre indiqué plus haut tout se passera sans problème.
    Bon courage... ;-)

  6. #6

    Kullanýcý Bilgi Menüsü

    Standart

    Translate in english please

  7. #7

    Kullanýcý Bilgi Menüsü

    Standart

    Alýntý ntahir Nickli Üyeden Alýntý Bu Linki Görmeniz Ýçin SupersatForuma Uye Olmanýz Gerekmektedir.
    Translate in english please
    Sorry...

  8. #8

    Kullanýcý Bilgi Menüsü

    Standart

    Translate English

    Converting your Kaon 570 in 570H
    Version 1.0 January 18, 2007
    Why should I make this transformation?
    Because there is more support for the Kaon long 570H (presumably to sell their new products) on the other hand there are still for the 570.
    What difference there is between a t'il 570H and 570?
    The 570H makes recordings on hard disk thing that will be more can be done on 570 after the change.
    Does the change is permanent?
    No, it is sufficient to withdraw the amendment to restore its 570H
    Is that the change is difficult to do?
    No, there is only one to lean on a wire and any manipulation on the motherboard.
    What is this famous modification?
    The fundamental difference between 570H and 570 is the Display.
    The 2 Display are not compatible! ! !
    Therefore disable part of the Display of 570H and accordingly after the amendment of the Display
    No longer function only partially.
    So in addition to the HD ... The Display will no longer be operational either?
    Yes, it's a price worth paying, but at least we will have a decoder that will work with the firmware 12.01.A5 which are updated regularly.
    There are still there other things to do apart from the change?
    Yes, once the amended its 570H HW become 12.01.A5 and it will not only save him the firmware appropriate but also change its Bootload him.
    ! ! ! BOOTLOAD CHANGE! ! ! ! MAMAN I FEAR! ! ! !
    Yes you are right, you should always be afraid to touch the bootload, but for our model of the two bootloads Kaon are mostly compatible with each other. If one mixes brushes it will not be too severe and we will always have access to the decoder by the ****** port to remedy the situation. (See "Tips" at the end of Doc)
    Well OK, "says the amendment still ... And long after I will see if I decide .... :-)
    Note:
    Although I have already made the change on several Kaon without ever having had recourse to
    JTAG aware that you are solely responsible for your actions.

    Well ... Going y. .. As already commented above, in addition to a change in physical Display it will also change the Bootload and firmware. So, the first thing to do is buy them if they are not included in the archive of this doc.
    The new bootload will 2.1.9V4 KaonTeam group.
    The firmware will be the last 12.01.A5 that you find on your favorite Upload.
    Get also bootload 1.1.9V4 KaonTeam group for the event or do you decide
    Reverse and thus find your decoder 570H.
    Ideally for the amendment is to proceed in that order.
    1-We save our first and favorite channels for the case or they would be removed. (Usually not)
    2-We entrust the bootload 2.1.9V4 in the Kaon.
    From that moment, and although the Kaon is operational it will not be possible through the ****** port to send anything at Kaon because we will have a Bootload which will be more compatible with the Display.
    3-We are changing our therefore Display as explained a bit further to make it compatible.
    4-Once reconnectons we changed it to the motherboard.
    5-We light the Kaon with the back button.
    After a few moments we will see "--" on Display
    6-We are preparing the KUP mode Enginer (space bar of your PC keyboard) with firmware 12.01.A5 we have found on the Internet.
    7-We support the button "Stand By" on the front of Kaon ... And
    Transfer firmware should begin.
    If there is a problem at the end of the transfer example ... " ERR: STB on-> PC "do not panic, things happen, just over the transfer from point 5
    When the transfer is completed we finished our modifications and our decoder is
    Operational.
    Now as Display is no longer fully functional starting the Kaon is a little different, so here are the steps to follow:
    When we light the Kaon by the switch back we see emerging on Display "--" which tells us that our product is in Stand By ... Unfortunately result of the amendment realized it is no longer possible to emerge from this mode via the remote control, it will have to hit 'Stand By "from the front to see the" on "on Display. Then, if the decoder still does not start we support on the button "Stand By" on the remote control to put it permanently on duty.
    This procedure should be repeated if we cut the decoder with the back button because once the decoder in the remote service is fully operational and can be smoothly and the light switch off with it (eg to update the firmware).

    Modification of the physical Display.
    Above all remember to remove the electrical outlet in your decoder.
    Disassembly of the Display is very simple, so I will pass details.
    Once Display dismantled and disconnected from the motherboard must withdraw at the end circuit-imprimé
    Power unsolder the small bridge .... D6
    This image has been resized. Click this bar to view the full image. The original image is sized 641x479.


    Then it will withdraw some wire connector Display, which connects to the motherboard. (The black is the No. 1)
    To remove the wires just press with a screwdriver very late in the grooves and shoot the son puts an end connector one by one. As a precaution once the wires should be removed isolate ends with a bit of cloth insulation.
    This image has been resized. Click this bar to view the full image. The original image is sized 643x450.


    We can only cut the lead to the tune of 11 printed circuit and extend it to the bridge J6 (one we removed at the beginning)


    This image has been resized. Click this bar to view the full image. The original image is sized 514x385.


    ! ! ! CAUTION NOT FOR YOU TO HOLE DECEIVED! ! ! And this is the work ... You will agree that it was not quite complex.

    How to reverse and get your good old 570H
    To realize in order:
    1. Load bootload 1.1.9V4 group KaonTeam
    2. Loading the firmware for the 570H
    3. Remove the changes made on Display:
    Remove the extension of the wire 11 and as a citizen it before it is shut down. Give all wires in the connector which has the motherboard. Give the bridge J6
    Hints:
    When Kaon lies with the Display original state but with the Bootload 2.1.9V4 it is not possible to transfer to the Kaon because communication is interrupted every few seconds by the Display. What do I do to get out?
    Two possibilities:
    Either change the Display as explained above
    Either on the Display connects to the motherboard but slightly pushing the connector and the transfer once started ... It quickly withdrew the connector to prevent the Display does interrupt the communication via the ****** port.
    When changing firmware it is possible that we pass a code of 4-digit PIN to a six-digit or vice versa. Here are a few codes of origin to try to get access to the Menu.
    0000
    Keys: Red Blue Green Yellow
    463330
    Although this will seem Doc perhaps a bit "complex" at the first reading ... Be confident that the amendment will be very easy to do and if you follow the order mentioned above this has been no problem.
    Good luck ... ;-)

  9. #9

    Kullanýcý Bilgi Menüsü

    Standart

    Eðer anlam bütünlüðü bozulmadýysa iyi çalýþma!!!

  10. #10

    Kullanýcý Bilgi Menüsü

    Standart

    thanks a lot dear

Sayfa 1/2 12 SonSon

Konu Bilgileri

Users Browsing this Thread

Þu an Bu Konuyu Gorunteleyen 1 Kullanýcý var. (0 Uye ve 1 Misafir)

Bu Konudaki Etiketler

Yer imleri

Yetkileriniz

  • Konu Acma Yetkiniz Yok
  • Cevap Yazma Yetkiniz Yok
  • Eklenti Yükleme Yetkiniz Yok
  • Mesajýnýzý Deðiþtirme Yetkiniz Yok
  •