Teşekkur: 
Beğeni: 
Philips
MD1.2E CTV
Service Mode
There is a small Service jumper to short on the small signal PCB. When the TV is in this first level service mode, you can go in the second level service mode by pressing both MENU
and - keys on top of the TV at the same time. There you can read much parameters and proceed with most of the adjustments. In fact this method let you use an ordinary Remote control but you also need to open the back
cover. With the special service remote control,
a special code is sent to enter the service mode. Philips
MG3.1E CTV
Service Mode
Option 1: In the TV-set itself is a 3-pin connector with which either SERVICE-DEFAULT or
SERVICE-MODE can be activated. This connector is depicted 0356 (SERVICE-PINS) on page K7 (TXT&CONTROL). Shorting pins 1-2
will activate SERVICE-MODE. Shorting pins 2-3 will activate SERVICE-DEFAULT. Option 2: Activate these modes using the remote control. Obviously option 2 is the preferred method because the settings have to be changed using a remote control anyway.... To activate SERVICE-DEFAULT: Press 0 6 2 5 9 6 and then
the [menu] button. The message `Service Default' appears and channel `SER T' will be selected. This only sets some settings to a preset value
(color/brightness/volume and such). This mode is primarily intended to be used when the non volatile memory has been replaced. It is then loaded with the default values. To activate SERVICE-MODE: Press 0 6 2 5 9 6 and then
the [i+] button. After pressing 0 6 2 5 9 6 the message `Dealer' should have appeared.
Do not worry about the channel changing while you press the numbers.
Service technicians have the means of entering service mode using a special remote control. Philips
29PT9416
MG7.1
CTV
Service Mode
Use the standard remote control an *** in a special sequence 0 6 2 5 9 6 followed by pressing the 'MENU' button. If the main menu also appears with the service menu just press
'MENU' again to clear it. The other way is to short the two service pins on the signal panel
(pins 2 and 3 of connector 0356). The advantage of this last method is that all the software protections are turned off.
Philips
Y6
CTV
Service Mode
Use the standard remote control an *** in a special sequence 0 6 2 5 9 6 followed by pressing the 'MENU' button. If the main menu also appears with the service menu just press
'MENU' again to clear it. Philips
VR210/58
VCR Modulator off
Without cassette. Press and hold SYSTEM till
'G591' appears. Press and hold CLEAR(CL) till
'MOFF' appears. Exit: TV/STANBY. Philips VR210/58
VCR Modulator on
Without cassette. Press and hold SYSTEM till
'MOFF' appears. Press and hold CLEAR(CL) till
'G591' appears. Exit: TV/STANBY. Philips VR220/58
VCR
Child Lock
Cancel
Press CHILD LOCK (***-simbol) on the RC for 5s with the VCR switched on. Philips
VR220/58
VCR Modulator on/off
Without cassette. Press and hold STOP on the
RC and then press STOP/EJECT on VCR.
Select the line 'MODULATOR' on the TV screen
or 'MOD+' in the display with P+/-. In the display select 'OFF' / 'MOD-' (modulator off) with VOL-
or 'MOD+' (modulator on). Confirm with OK. Exit with MENU
Philips
VR220/58
VCR Modulator preset
Without cassette. Hold the STOP button on the RC. In addition press the STOP/EJECT button on the VCR until the pre-set modulator frequency appears in the display, e.g. 'M591'
(591MHz or 36 ch. UHF). Select line 'OPTIMIZE FREQUENCY' using P+/-. Enter new
modulator frequency with the numbers 0-9. In line 'SOUND SYSTEM' select the TV system using VOL+/-. 'G' = PAL B/G. 'K' = SECAM D/K. Confirm with OK. 'STORED' will appear briefly on the screen.
Philips
VR220/58
VCR Reset to factory settings
Disconect from the mains power supply. Press and hold the STANDBY/ON button on the device and reconnect to the mains power supply. Release the button when 'OSD' appears in the VCR display.
Philips
VR400/58
VCR
Auto ST-BY
off
Press and hold STOP till [] appears. Philips
VR400/58
VCR Modulator off
Without cassette. Press and hold SYSTEM till
'G591' appears. Press and hold CLEAR(CL) till
'MOFF' appears. Exit: TV/STANBY. Philips VR400/58
VCR Modulator on
Without cassette. Press and hold SYSTEM till
'MOFF' appears. Press and hold CLEAR(CL) till
'G591' appears. Exit: TV/STANBY. Philips VR400/58
VCR Modulator preset
Without cassette. VCR st-by. Press and hold
SYSTEM till 'G591' appears. System change:
SELECT.
Freq. Change: P +/-.
Store: OK. Exit:
TV/STANBY.
Revox D-TV C9003
CTV
Service Mode
On the local control press function *** five times
(indication "Service" will appear), afterwards within a sec. press *** "MEN" on the remote control.
Store: X. Exit: TV.
Alıntı
Yer imleri