Step 1: Open the package, familiar with all the components. If you have ordered 20 pin configuration, you will not get B and G in the picture. If you have ordered 10 pin configuration, you will not get A and F.
Step 2: Cut one 100 Ohm resistor as shown in picture.
Step 3: Put some melted solder into the cup 2, 3, 4, 5, 13, and 18 to 25 of the DB25 male connector as shown in picture.
Step 4: Use the cutted resistor conductor to connect 18-25 pin together.
Step 5: Cut the rest resistors as shown in picture.
Step 6: Solder 5 resistors onto the DB25 connector (pin 2,3,4,5 and 13).
Step 7: Cut the resistor conductors as shown in picture.
Step 8: Put some melted solder onto the bare conductors.
Step 9: (10 pin configuration) Cut and strip the flat cable as shown.
Step 10: (20 pin configuration) Cut and strip the falt cable as shown.
Step 11: (10 pin configuration) Put some melted solder onto the bare wires, then put the heat shrink tube onto the wires.
Step 12: (20 pin configuration) Put some melted solder onto the bare wires, then put the heat shrink tube onto the wires.
Step 13: (10 pin configuration) Solder flat cable onto the DB25 connector as shown in picture.
Step 14: (20 pin configuration) Solder flat cable onto the DB25 connector as shown in picture.
Step 15: (10 pin configuration) Put heat shrink tubes onto the resistors to prevent short circuit.
Step 16: (20 pin configuration) Put heat shrink tubes onto the resistors to prevent short circuit.
Step 17: (10 pin configuration) Align wires on the IDC connector. Make sure line 1 is under the little triangle as shown in the picture. Then squeeze two halves of the IDC connector together until both retainer loops snap over the ribs and lie flat against the sides.
Step 17: (20 pin configuration) Align wires on the IDC connector. Make sure line 1 is under the little triangle as shown in the picture. Then squeeze two halves of the IDC connector together until both retainer loops snap over the ribs and lie flat against the sides.
Step 19: (10 pin configuration) Put the strain relief onto the IDC connector. Squeeze the strain relief and the IDC connector.
Step 20: (20 pin configuration) Put the strain relief onto the IDC connector. Squeeze the strain relief and the IDC connector.
Step 21: Prepare the DB25 shell as shown in picture.
Step 22: (10 pin configuration) Take the two wire holders and clamp them onto the cable. Pay attention to red arrow in the picture.
Step 23: (20 pin configuration) Take the two wire holders and clamp them onto the cable. Pay attention to red arrow in the picture.
Step 24: Put the DB25 connector into one half of the DB shell.
Step 25: Close up the DB25 shell. Use the remaining two screws and nuts to finish the assembling.
Step 26: Close up the DB25 shell. Use the remaining two screws and nuts to finish the assembling.
Step 27: Congratulations! You are done! resimdeki kabloyu kullanacaðýnýz diye bi kaide yok renkli koblo kullanýrsanýz bence daha iyi olur ben öyle yapmýþtým uclarý karýþtýrmamak için
kablonun ucuna baðlý gördüðünüz soketi yapmanýza gerek yok TDO, TRST, TDI, TCK, TMS bu uçlarý unutmayýn
resimler alýntýdýr uzun zamandýr uðraþmýyorum çünki
cihazýn jtag giriþine uygun kablolarý lehimliceksiniz iþ bu kadar
Bu Linki Görmeniz Ýçin SupersatForuma Uye Olmanýz Gerekmektedir.
buda pin baðlantý noktalarý resmi incelersen bacaklarý nasýl baðlanacaðý hakkýnda
flaþ programlarken kullanacaðýnýz programý da aþaðýdaki linkten indirebilirsiniz
Bu Linki Görmeniz Ýçin SupersatForuma Uye Olmanýz Gerekmektedir. Bu Linki Görmeniz Ýçin SupersatForuma Uye Olmanýz Gerekmektedir.
istediðinizi kullanýn
bu iþlem ýbm iþlemcili bordlarý desteklemez
flaþý sökerek detekleyen bordda da yapabilirsiniz
bununla sadece flaþdump atabilirsiniz
rs232 den attýðýnýz programý atamassýnýz
örnek baðlantýlar Bu Linki Görmeniz Ýçin SupersatForuma Uye Olmanýz Gerekmektedir.
sunyy-kaon Bu Linki Görmeniz Ýçin SupersatForuma Uye Olmanýz Gerekmektedir.
vestel
Konu yargýç_1 tarafýndan (09-02-2009 Saat 10:48 ) deðiþtirilmiþtir.
Bildindigi uzere sadece iki turlu flash kiliti vardir:
Birincisi hardware kilit
Ikincisi software/hardware combinasyonu kilit
Asagida resmi gosterilen flaslarin ayni sifre configurasyonu ve hardware desifresi
vardir Bu Linki Görmeniz Ýçin SupersatForuma Uye Olmanýz Gerekmektedir.
Type1 " Harsdware Unlock" :
Bu Linki Görmeniz Ýçin SupersatForuma Uye Olmanýz Gerekmektedir.
Bu Linki Görmeniz Ýçin SupersatForuma Uye Olmanýz Gerekmektedir.
Notlar:
1-WP numarasi sifre atmel flaslarinda bulunmamaktadir ve Vpp, WP numarasi oteki sozu edilen oteki flaslarda bulunmaktadir.
2- Vpp,WP# sifreleri control sifreleridir.
3-Bilgisayarinizin paralel portunun (kapisinin) EPP/ECP ye kuruldugundan emin olmaniz
gerekir. Eger degilse BIOS degerlerini EPP/ECP ye donusturun. Ayrica Paralel port
adresini not alin. Normal olarak 378 dir.
Islemler:
1-Flash Atmel ise VPP sifresinin dogrudan dogruya processor'a yada PNP transistorunun
collector'una bagli oldugundan emin olun.
Eger flash Atmel'den baska ise WP numarasinin ve Vpp nin dogrudan dogruya processor'a yada PNP transistorunun collector'una bagli oldugundan emin olun.
2-Eger dogrudan dogruya processor'a bagli ise, onlARI VE vpp yi birbirine bagliyan
kabloyu kesin (Atmel flaslari icin), oteki flaslar icin VPP ve WP# 3.3v ye baglayin.
Eger dogrudan dogruya PNP trasistor'unun collector'una bagli iseler onlari direct
olarak herhangi 3.3v ye baglayin. Bu durumda kesmenize gerek yok.
NOte: Cogu alicilarin WP numarasi ve VPP sifresi birbirine baglidir veya WP numarasi
3.3v vcc sifre 47 flasda ve Vpp Pnp transistorunun collector'una bagilidir.
3-JTAG paralel fisini bilgisarinizin paralel portuna baglayin ve aliciniza power verin.
(Electrige baglayin demek istiyorlar zannedersem.)
4-Wall 'i baslatin. Adimlar:
a)Ok tiklayin uyari (Warning) mesaginda.
b)Reset Up 3 kere tiklayin. Her tiklamadan sonra uyari mesaginda ok ye tiklayin.
c)Wall'i bilgiyarinizin ekraninda acik birakin.
5-J***s baslatin. Processorunuzin tipini asagidaki sekilde tanimasi gerekir :
Device ID : 0x1D405041
Device : STi5518BVC
6-IDR modelini secin
7-Flash programining'a tiklayin. Hemen programlamaya baslamasi gerekir.
8-J***s flash tipini hemen tanimasi gerekir. Programing Panelini aciniz. Eger Mfg veya
Device ID hakkinda Error (Yanlis) mesagi alirsaniz hersey yolunda gitmemis demektir.
J***s.def documaninin dogru oldugunu teyit edin.
9-Flashi silip yeniden programlayabilirsiniz.
10-Programlamayi tamamladiginizda IRD yi fisden cikarip oteki baglantilarini kapatin.
Bu Linki Görmeniz Ýçin SupersatForuma Uye Olmanýz Gerekmektedir.
Islemler:
Yukaridaki ilk 6 adimi ayni sekilde uygulayin.
7-Bu adim Processor'a (Omega) emir gonderip bize yolu acar. Development Panel'ina
tiklayin. Orada soylenen adimlara onem vermeyin. Sadece Ok'ye tiklayin.
8-Development Panelinin Sol tarafinda asagidakini yazin:
Arkadaþým bu uygulamayý gm 30300 için uygulayabilirmiyiz, bu cihaza uyan flaþ programý hangisi... bu uygulamayý rs 232 kablosuyla direkt cihazla bilgisayar arasýnda baðlantý kurarak flaþý silip yükleyemeyiz mi?
hasan Nickli Üyeden Alýntý
Bu Linki Görmeniz Ýçin SupersatForuma Uye Olmanýz Gerekmektedir.
Arkadaþým bu uygulamayý gm 30300 için uygulayabilirmiyiz, bu cihaza uyan flaþ programý hangisi... bu uygulamayý rs 232 kablosuyla direkt cihazla bilgisayar arasýnda baðlantý kurarak flaþý silip yükleyemeyiz mi?
yukarýda herþeyi anlattým demekki okumamýþsýnýz
hala ayný þeyleri yazýyosunuz yukarý bakýn hasan bey herþeyi anlattým daha ne soruyosunuz bu konuda bi sürü soru soran arkadaþlara en basit þekilde anlatmaya çalýþtým yukarýda rs232 ile bu iþ olmaz demiþim
Konu yusufcuk tarafýndan (09-02-2009 Saat 15:13 ) deðiþtirilmiþtir.
Yer imleri